View Single Post
Old 03-11-2007, 09:44 AM   #10
susies1955
Turning the Heel
 
susies1955's Avatar
 
Join Date: Sep 2005
Location: northern NY
Posts: 594
Thanks: 0
Thanked 3 Times in 2 Posts
Send a message via AIM to susies1955
Meg gave you some great tips.
There is a yahoo group that is wonderful. Here is the link:
http://groups.yahoo.com/group/incred...ermachineclub/
Here are some tips I had saved from the Bond site I think.
Susie

USM SETTING UP
Use a flat surface with a "true" bottom, like a piece of hardwood board, like a long pre-cut shelf available at hardware store/home center is a good choice. Bond also carries knitting tables.
Do not screw clamps on too tightly. This could raise the back of the bed and cause the needles to go out of alignment.
Check that there are no raised retainer bars across the bed. These are the green bars that hold in the needles. If any are raised slightly you can push them down with your finger or use a small hammer with fabric or rubber as protection to tap them down into place.
Do not bear down on the carriage or it could be difficult to knit. Just hold down the handle enough to keep the keyplate in place.

SOLUTIONS TO COMMON PROBLEMS
Problem: Carriage jams at the beginning of the row.

Solution #1: Remember to hold back the hem against the bed at the beginning of the row so the front of the carriage will clear the hem.

Solution #2: Be sure the green stripper plate on the underside of the nose of the carriage runs just below the needles. It is supposed to run just under the needles and slightly raise them as it knits.

Check to see if the yarn has wrapped around one of the green stripper plates on the underside of the carriage. Using your finger, release the yarn from around the plate, pull up the yarn that was caught on the plate and continue to knit the row. To prevent this from happening in the future, be sure to hold the yarn at the beginning of the row before you push the carriage, until you see the first needle begin knitting the yarn. For owners of the ISM model, the yarn has to be held more carefully for the USM since the carriage front is open.

Problem: Carriage jams after a few stitches.

Solution: Check to see if the yarn has wrapped around one of the green plates on the underside of the carriage. Release the yarn from around the plate, pull up the yarn and continue to knit the row. To prevent this from happening in the future, be sure to hold the yarn at the beginning of the row, until you see the first needle begin knitting the yarn. For owners of the ISM model, the yarn has to be held more carefully for the USM since the carriage front is open.


Problem: Carriage jams in the middle of the row.

Solution #1: Lift up the handle of the carriage and check to be sure all the needles are either in non-working, working, forward working or holding position. If there is a needle out of line, it can hit on the "bounce bar" on the underside of the keyplate. You will be able to see this through the tinted keyplates.

Solution #2: Be sure the retainer bars are flat across the bed (see above) and you are not bearing down on the carriage.

Solution #3: If you have a row counter attached to your machine, remove it while you're learning.

Problem: Carriage jams at the beginning of the row after you have knitted a row.

Solution: Be sure the last row was knitted completely. You should knit the row until the last needle stops moving or it will be difficult to knit the next row.

Problem: Difficult to knit completely across row.

Solution: Be sure there is enough free yarn coming from the pull-skein. If the yarn is pulling directly out of a new ball or if it gets caught on something on your table, it will be difficult to knit the row.

Problem: Knitting or hem falls off at the beginning of the row.

Solution: Be sure to hold the yarn at the beginning of the row and to be sure it feeds through the yarn guide in the front of the carriage. If it is pulled out or comes out by not holding it, there is no yarn to feed into the needles and all the stitches will drop. For owners of the ISM model, the yarn has to be held more carefully for the USM since the carriage front is open.

Problem: After knitting a few rows, carriage is stuck at the beginning of the row.

Solution: Because by nature, knitting curls at the sides, which could catch the edge of the carriage. Be sure the knitting is back against the bed and one of the green plates on the underside of the carriage isn't hitting the knitting.

Problem: Mistake made or too many rows knitted.

Solution: Just rip out the mistake row or extra rows. Be sure to unlatch the first stitch, which is usually a bit tighter than the others. See your instructional video on how to rip out a row.

Problem: Mistake made in the middle of the row and carriage is stuck.

Solution: Lift up the keyplate and slide the carriage back to the beginning of the row. Then rip out the stitches knitted on that row. Push the needles into either working or forward working position. Pull up the loose yarn and knit the row again.

Problem: I'm getting loops over the needles and nothing is knitting. What's wrong?

Solution: Most likely the keyplate is not inserted properly. Be sure the back edge of the keyplate is inserted between the two "shelves" at the back of the carriage. The keyplate will have to be pushed down slightly, but not forced down. Also, be sure not to try to insert the keyplate unless all the needles under the carriage are in non-working position.

ABBREVIATIONS
alt alternate
approx approximately
beg beginning
cm centimeters
COL carriage on left
cont continu(e)(ing)
COR carriage on right
dec decreas(e)(ing)
foll follow(ing)
FWP forward working position, stitches just behind open latches
inc increas(e)(ing)
HP holding position
K knit
KP keyplate
LHS left hand side
M1 pick up loop lying between needles and K into back of it
mm millimeters
NWP non working position
P purl
patt pattern
psso pass slipped st over
rem remain(ing)
rep repeat
RS right side
RHS right hand side
sl slip
st(s) stitch(es)
st st stocking stitch
tog together
WP working position
WS wrong side
WY waste yarn

How long does it take to learn to use the machine?
To learn the basics, just one evening - or a weekend, if you want to go through the complete instruction book.

How long does it take to make a basic sweater or afghan?
You can make an adult sweater or large afghan in two evenings, a child's sweater, smaller afghan or throw in one evening.

Can I use hand knitting patterns?
Yes. Information on how to convert hand knitting patterns for use on the machine are included in the pattern book that comes with your machine. Directions on how to short row are here.

Can I add hand knitting or crocheted sections fo my machine-knitted projects?
Yes. You can knit the back and sleeves on the machine and hand knit the front. Or you can machine knit part of the front, then take the knitting off the machine and hand knit a yoke. You can do the same for crochet, especially with afghans (edgings, joinings, panels, etc.)

Can I get more patterns for my machine?
Yes. Your machine will come with a brochure of other accessories, videos and pattern books that are available for your machine. You can also get Free Bond USM Patterns.

What kinds of yarns can I use on my machine and do I have to buy special types of yarns?
You can use between a sport weight and chunky weight yarn. You can also use fancy yarns such as mohair (or brushed yarn) and bouclé as well as different yarns mace from acrylic, cotton, wool, mohair and lots more.

What happens if I get stuck? Is there a help line I can call?
Yes. The phone number for the help line is printed on the information that comes with your machine. There is no charge for this help except the cost of the long distance call.

What type of warranty comes with the machine?
The machine comes with a limited lifetime warranty against product defects. You may register your machine for warranty online.

What are the main differences between the Incredible Sweater Machine or Bond Classic and the Ultimate Sweater Machine?
The needle bed is the same. The carriage is quite different and incorporates all the “wishes” of Sweater Machine knitters over the years: the front of the carriage is open (no fabric guide) so doing intarsia “on the fly” (as you knit) and other changing of yarn, such as for stripes, is especially easy. The carriage also has a built-in tripper for the row counter. There are six different keyplate sizes to match every size hand knitting needle from a 6 through a 10. The color of the carriage is plum and the keyplates are a transparent green. There’s a new pattern book, instruction book and video and lots of Accessories, Pattern Boooks and Instructional DVD's.
__________________
Birth-date: 10/19/1955
Location: northern NY
I enjoy reading, quilting (started 10/11/2003), bread baking, purse making, making fabric bowls. I use to macramé and decorate cakes.
I started hand knitting (10/01/2005) and got my embroidery machine for Christmas 2005. I had 2 Bond Incredible Sweater Machines given to me in Feb. of 2007 that I'm really enjoying. http://susies1955.myphotoalbum.com/
http://susieshobbyspot.blogspot.com/
susies1955 is offline   Reply With Quote