Reply
 
Thread Tools Display Modes
Old 02-28-2008, 02:43 PM   #1
sideways
Ribbing the Cuff
 
Join Date: Oct 2007
Posts: 30
Thanks: 9
Thanked 17 Times in 9 Posts
DIY ball winder
Materials:
drill
wooden dowel or knitting needle #10 or smaller
masking tape

Tape the yarn along the dowel in two places. Start the drill slowly, using the other hand to control the tension as it winds. As it builds, start moving your tensioning hand back and forth quickly so it wraps somewhat diagonally. Wind in between the tape (not over it) so you can remove it when you're done. This makes a center-pull ball. After winding, just pull the yarn right through the tape and slide the ball off the dowel.

Hints:
Masking tape will release easily. Other tapes will work fine, but might be harder to peel off. The tape is only there for long enough to get things started and keep the loose end away from the drill.

Form the ball as close to the drill as you reasonably can (without winding over the tape). The closer it is, the better balance it will have while winding. The ball is messier than one made on a regular winder, but it works. I'm going to do the last few layers by hand, just to neaten up the outside.

I have a vise that isn't set up yet. Ideally, I would mount the drill in a vise to keep it steadier than it is in my hand.

A #10 needle fits my drill perfectly. I tried a #11 but the taper was too long and the chuck couldn't tighten properly. A pencil should work too, if it's not too short. Anything long, skinny & round.

Next....I want to see if I can hack another ball winder using my sewing machine's bobbin winder mechanism, lol. The foot control would allow me to use both hands to control the winding.
Attached Thumbnails:
Click image for larger version

Name:	drill1.jpg
Views:	451
Size:	30.3 KB
ID:	47116  Click image for larger version

Name:	drill2.jpg
Views:	432
Size:	14.8 KB
ID:	47117  Click image for larger version

Name:	drill3.jpg
Views:	424
Size:	20.9 KB
ID:	47118  
__________________
my blog
sideways is offline   Reply With Quote
The Following 2 Users Say Thank You to sideways For This Useful Post:
Debkcs (04-21-2008), lmsloman (03-01-2008)

 

This advertising will not be shown to registered members. Join our free online community today!

Old 02-28-2008, 02:57 PM   #2
mwhite
Instepping Out
 
mwhite's Avatar
 
Join Date: Sep 2007
Location: SC
Posts: 2,559
Thanks: 1,000
Thanked 919 Times in 805 Posts
Smart Cookie!!!

The tension discs on your sewing machine should work good, just loosen them enough to accept the yarn without binding it.

Industrial Sewing Machines actually have a separate bobbin winder, if you can get your hands on these, they are fantastic! We use one in the shop for winding fishing reels. Mary
__________________
Mary
custoMaryevents
I'm MWhite on Ravelry, too...add me to your friends
mwhite is offline   Reply With Quote
Old 02-29-2008, 02:04 PM   #3
lelvsdgs
Working the Gusset
 
lelvsdgs's Avatar
 
Join Date: Sep 2007
Location: Humboldt County CA
Posts: 1,366
Thanks: 1,016
Thanked 431 Times in 404 Posts
You are a genius!!! I knew there had to be a reason to buy an electric drill! Maybe I'll get one for Mother's Day
I just saw in JoAnn's the other day a battery (I think) powered bobbin winder that just winds bobbins. It wasn't priced so I don't know the cost but it might be worth looking into!
__________________


http://www.frappr.com/knittinghelp

Knitting is saving my sanity


OTN: Hats, hats and soon, socks!

FO:Hats-about 6 of them and a scarf for a coworker

Last edited by lelvsdgs : 02-29-2008 at 02:05 PM. Reason: bobbin winder info
lelvsdgs is offline   Reply With Quote
Old 02-29-2008, 03:28 PM   #4
sideways
Ribbing the Cuff
 
Join Date: Oct 2007
Posts: 30
Thanks: 9
Thanked 17 Times in 9 Posts
Lelvsdgs --- Thanks

A cheap electric drill costs just a little more than a ball winder, but they're waaaaay more useful. I've used mine to make cording. I put a hook-shaped piece of wire (coat hanger again!!!) in the chuck and go to town.

I wonder if a battery bobbin winder would have enough juice and torque to wind a ball of yarn. A bobbin and thread weight almost nothing; a ball of yarn can weigh quite a bit more. But you could try it, if it doesn't work out you could probably return it.
__________________
my blog
sideways is offline   Reply With Quote
The Following User Says Thank You to sideways For This Useful Post:
lmsloman (03-01-2008)
Old 04-21-2008, 12:58 PM   #5
justsmi
Ribbing the Cuff
 
justsmi's Avatar
 
Join Date: Jan 2008
Location: Buffalo, NY
Posts: 42
Thanks: 5
Thanked 5 Times in 5 Posts
i tried this with my dremel, i cant seem to get it to shape a ball per se, i get little hourglass shaped skeins, that seem to fall apart at the ends, and are very tight in the center. any suggestions would be greatly appreciated...
__________________
Thanks,
Courtney
i #27
Go SABRES!!!
justsmi is offline   Reply With Quote
Old 04-21-2008, 01:05 PM   #6
Debkcs
Instepping Out
 
Debkcs's Avatar
 
Join Date: Aug 2007
Location: Salem, OR
Posts: 2,919
Thanks: 384
Thanked 1,281 Times in 1,192 Posts
That's brilliant!! I have a drill, why buy a winder?

DH is going to laugh his butt off, but then, he never uses the drill for anything, it's mine. This is such a great idea, especially as I've three skeins that need to be wound.

Have any good ideas for a swift?
__________________
I LOVE THIS SITE!

"All good things and every perfect gift is from above, coming down from the Father of Lights who cannot change."
James 1:17
Debkcs is offline   Reply With Quote
Old 05-15-2008, 04:32 AM   #7
sideways
Ribbing the Cuff
 
Join Date: Oct 2007
Posts: 30
Thanks: 9
Thanked 17 Times in 9 Posts
Originally Posted by Debkcs View Post
Have any good ideas for a swift?

Sorry that this is a late reply. I posted a swift here at KH. I also put together detailed directions over at Instructables.com.

Originally Posted by justsmi View Post
i tried this with my dremel, i cant seem to get it to shape a ball per se, i get little hourglass shaped skeins, that seem to fall apart at the ends, and are very tight in the center. any suggestions would be greatly appreciated...

I have a Dremel too. Dremels work by taking lots and lots of little "bites" out of something at a very high rate of speed, even the ones that have variable speed. Regular drills work more on the power of their torque; they spin slower but have more "muscle" behind the spin. That's why a drill can force screws into solid wood if you're building a deck, but Dremels can't.

My guess is a Dremel spins too fast to allow you the control you need to form the ball as it winds, even at the slowest speed (if it has one).

Sorry if I sound like a know-it-all. MY ex was a big do-it-yourselfer, and for many years I gophered/helped during all sorts of home repair and car maintenance projects. I learned all sorts of useful stuff about tools and gadgets and traditionally-male subjects.
__________________
my blog
sideways is offline   Reply With Quote
Old 05-15-2008, 06:08 AM   #8
anniep
Ribbing the Cuff
 
Join Date: Mar 2008
Location: Melbourne, Australia
Posts: 33
Thanks: 11
Thanked 9 Times in 9 Posts
I laughed when I saw your photos Great idea! So inventive!
anniep is offline   Reply With Quote
Old 05-15-2008, 09:19 AM   #9
knitgal
Working the Gusset
 
knitgal's Avatar
 
Join Date: Aug 2007
Location: Ontario, Canada
Posts: 1,710
Thanks: 1,249
Thanked 987 Times in 655 Posts
You are way too clever! Way to go on making both of those. Do you have any other inventions? I don't know if the DBF would like if I stole the drill to make a bill winder!
__________________
Ann

OTN: Corona, Miter square blanket, Charity blankets
FO: Forest Canopy Shawl, Easy Baby Bootees, Kitty Pi, Ms. Marigold, Twinkle Toes, Josh's socks, Hedera socks, Spring Beret, Ashley's Birthday socks, Socks for the DBF's mom, grey socks for the DBF, my first socks, reversible cable scarf, ribbed hat for the BF, Manos Del Uruguay afghan, and a whole bunch of dishcloths!


knitgal is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Just got a ball winder! laikabear General Knitting 11 01-17-2009 05:59 PM
ball winder or cone winder??? Lucy78green Creating Yarn: Spinning, Dyeing, etc. 4 11-02-2008 06:32 PM
ball winder Duessa How-to Questions 7 09-15-2008 02:39 AM
I just got a ball winder!! IrishKnitter General Knitting 17 02-21-2007 12:32 PM
Ball winder janie General Knitting 6 08-09-2006 08:19 PM

All times are GMT -4. The time now is 03:55 AM.